Beginner’s Handbook for Detecting and Repairing Slab Leaks

Introduction

Slab leaks can cause large-scale water damage. Most homeowners find this a nightmare because it takes some time to be noticed. Suddenly, you see that even though your consumption hasn’t changed, your water bill has increased.

According to the U.S. Ministry of Energy, a household uses approximately 64 barrels of water on average per day. However, the cost of water will skyrocket if you have a slab leak, mainly if it takes some time to notice. Finding a slab leak in Riverside early on can save your funds and keep you safe.

What is a Slab Leak in Riverside?

If your house has a crawlspace or basement, you shouldn’t be concerned about a leaky slab. However, under-slab plumbing is a feature of homes constructed on slab foundations. In this setup, the plumbing pipes are encased in cement.

Anything tucked under cement is difficult to troubleshoot and repair. Before assuming that someone ran the water pipes beneath your foundation incorrectly, let’s discuss the most economical way to get water into your home.

The copper pipelines are connected at manifolds, and each is routed to different appliances in your home. These water lines supply cold and hot water for your showers and toilets.

A pinhole leak can occasionally occur in a particular pipeline. And there you are! There’s a slab leak!

But what causes slab leaks and how common are they? The following section will provide the answers to those queries. Let’s begin!

Why Do Slab Leaks Occur?

A slab leak in Riverside can have many causes. The original plumbing system may eventually give way under the load of your house if it was built poorly or with inferior materials. Additional potential reasons could be corrosion and abrasion. When water passes through pipes, the pipes naturally grow and shrink. The pipes may start to wear down and develop leaks if they are near concrete or gravel. This is because the pipes may start rubbing against these materials.

Similar to this, water lines can corrode as time passes if they are near acidic soil or are subjected to hard water regularly. This is particularly prevalent in houses with metallic or copper plumbing. Corrosion may eventually cause leaks and ruptures. Very high pressure of water that explodes pipelines or foundational shifts caused by environmental conditions such as earthquakes or drastic weather changes are other sources of leaks.

6 Common Signs of a Slab Leak in Riverside

Slab leaks operate secretly just below your feet as we’ve already discussed. Then, how can you tell you’ve got a leaky slab?

1. Apply your senses! Yes, you got it right. you need to touch and smell to detect a slab leak in your home. Surprised!! Well, here it is. If water is rising beneath your floor, be sure to monitor the temperature. If the water feels hot and you don’t have radiant heat, you may have a leaky slab from a hot pipeline.

2. An additional detecting instrument is your nose. Your home has too much moisture if you smell mold growing there. If you’re still not able to locate the source of the smell, give your plumber a call. They are adept at Slab leak detection in Riverside and can easily locate potential sources of mold growth, like slab leaks.

3. Leaks are an early warning indicator of a problem that needs to be fixed. Water has been leaking from the pipes because of the existence of puddles and other leaks. This will likely soak into the drywall.

4. If there are problems with the showers or toilets, it might be a sign of a broken water line.

5. Determine which appliances are in backup power to assist in locating the potential leak and search for additional leakage indicators. Try ruling out other potential reasons for the backup if this seems to be the only sign of a leak.

6. Unusually large water bills? One possible cause could be a slab leak. To find and investigate any plumbing issues on your property, get in touch with a licensed plumber.

Best Slab Leak Detection in Riverside

Even though patching a leaky slab may seem difficult, it’s crucial to act quickly to stop additional damage.

Locating the leak is the first stage in fixing a slab leak in Riverside. In case the leak’s location is unknown, it can be located using a specialized camera system. After the leak is located, it can be sealed with epoxy, using water at high-pressure jetting, or other techniques for repairing pipes. If the damage caused by the leak is significant, it might be required to eliminate and substitute the damaged slab or pipe section.

It is advisable to contact a reputable plumbing business for assistance with this process as it calls for specific equipment and knowledge.

When handling a slab leak in Riverside, it’s critical to take preventive action. These include inspecting the water lines and seals, searching for wall or foundation cracks, and increasing insulation. By taking these preventive measures, you can steer clear of plumbing issues and expensive repairs. Hire a reliable Riverside plumber to identify and fix any slab leaks you suspect right away.

Final Takeaway

Finding and fixing slab leaks can be difficult for homeowners, but it is entirely doable with the correct knowledge and assistance. By being aware of the warning indicators of a leaky slab and taking the actions recommended in this handbook, you can prevent more harm from happening to your property. It’s important to remember that reducing the expenses and inconveniences related to a slab leak in Riverside requires early detection and swift action.

Take action to stop a slab leak in Riverside before it leads to destruction. To ensure your safety, let us repair the broken pipes. Give EZ Plumbing a call right now!

FAQS

What is the slab leak detection cost?

While fixing a slab leak typically costs $2000, slab leak detection generally costs in the range of 150 to 400 dollars.

Can you suggest any slab leak detection near me?

EZ Plumbing is the right choice for all your plumbing needs 24/7.